series fr01 10mm dip rotaries www.nkk.com g4 indicators accessories supplement tactiles keylocks pushbuttons illuminated pb slides programmable rockers touch tilt toggles g rotaries electrical capacity (resistive load) switching rating: 100ma @ 5v dc nonswitching rating: 100ma @ 50v dc other ratings contact resistance: 100 milliohms maximum; 30 milliohms maximum for contact point insulation resistance: 1,000 megohms minimum @ 250v dc dielectric strength: 250v ac minimum for 1 minute minimum mechanical life: 10,000 detent operations minimum electrical life: 10,000 detent operations minimum notes: a detent operation is one actuator position operation or stepping. a cycle is one 360 rotation. 10,000 detent operations equal 625 cycles for hexadecimal devices or 1,000 cycles for decimal devices. nominal operating torque: metal shaft: 0.009nm for decimal devices; 0.011nm for hexadecimal devices all other actuator types: 0.008nm for decimal devices; 0.01nm for hexadecimal devices contact timing: nonshorting materials & finishes actuators: screwdriver and plastic shaft - glass fber reinforced polyamide (ul94v-0); dial - polyoxymethylene; metal shaft - brass with nickel plating bushing : brass with nickel plating (for metal shaft model) outer case: glass fber reinforced pbt (for metal shaft model) housing & base: glass fber reinforced polyamide (ul94v-0) movable contacts: copper alloy with gold plating stationary contacts: phosphor bronze with gold plating terminals: phosphor bronze with gold plating terminal cover: polyamide (right angle model only) bracket: phospher bronze with tin plating (for metal shaft model) environmental data operating temperature range: C25c through +85c (C13f through +185f) humidity: 90 ~ 95% humidity for 240 hours @ 40c (104f) vibration: 10 ~ 55hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 5 minutes; 3 right angled directions for 2 hours shock: 50g (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) processing soldering: wave soldering recommended. see profle a in supplement section. note: during wave soldering process, set the switch to the following position: fr01fr10p, fr01fr16p, fr01kr10p, fr01kr16p, fr01sr10p, FR01SR16P, fr01ar10pb, fr01ar16pb, fr01ar10hb, fr01ar16hb: 0 position; fr01fc10p, fr01kc10p, fr01fc10h, fr01kc10h, fr01sc10p, fr01ac10pb, fr01ac10hb: 7 position; fr01fc16p, fr01kc16p, fr01fc16h, fr01kc16h, fr01sc16p, fr01ac16pb, fr01ac16hb: f position manual soldering: see profle a in supplement section. cleaning: these devices are not process sealed. hand clean locally using alcohol based solution. custom process sealed version available; contact factory. standards & certifications flammability standards: ul94v-0 rated actuator, housing and base the fr01 series rotaries have not been tested for ul recognition or csa certifcation. these switches are designed for use in a low-voltage, low-current circuit. when used as intended, the results do not produce hazardous energy. general specifcations
series fr01 10mm dip rotaries www.nkk.com g5 indicators accessories supplement tactiles keylocks pushbuttons illuminated pb slides programmable rockers touch tilt toggles g rotaries actual size compact dimensions and low profle allow high density mounting and close stacking of pc boards. highly visible legends and choice of screwdriver, shaft or dial actuators with arrow position indication provide trouble-free code setting. knob actuator also available. real or complement code setting identifed by color-keyed actuator. detent mechanism gives crisp, positive action for accurate switch setting. crimped terminals ensure secure pc mounting and prevent dislodging during soldering. cam activated movable contact and gold contacts assure contact reliability and continuity. surface mount model with screwdriver actuation available and shown in the surface mount section. contact factory for custom models with .200 (5.08mm) terminal spacing. distinctive characteristics
series fr01 10mm dip rotaries www.nkk.com g6 indicators accessories supplement tactiles keylocks pushbuttons illuminated pb slides programmable rockers touch tilt toggles g rotaries typical switch ordering example (2.1) .083 (0.8) .031 (9.6) .378 f screwdriver actuation adjusted with a fat tipped screwdriver install knob before mounting on pcb for right angle type; it should not be removed once mounted. when mounting, align slit in knob with arrowhead on actuator. polyamide black knob with transparent fange at4180 optional snap-on knob actuators are fully rotational either clockwise or counterclockwise. actuator colors: orange for real coded devices; yellow for complement coded devices. (6.7) .264 (0.8) .031 (1.1) .043 (4.0) .157 01 through-hole mounting p fr bracket no code no bracket *b with bracket * for actuator a only pc terminals p straight h right angle r 16 circuits r real coded (orange actuator) c complement coded (yellow actuator) color not applicable to actuator a positions 10 decimal 16 hexadecimal k actuation f screwdriver k plastic shaft s dial (for straight terminals only) *a metal shaft (for optional knobs) * must be used with bracket s 01 packaging s stick-tubes: fr01f, fr01k, fr01s 50 pieces/stick fr01a 25 pieces/stick mounting 01 through-hole description for typical ordering example fr01kr16p-s hexadecimal positions real coded straight pc terminals plastic shaft packaged in stick-tube
series fr01 10mm dip rotaries www.nkk.com g7 indicators accessories supplement tactiles keylocks pushbuttons illuminated pb slides programmable rockers touch tilt toggles g rotaries optional knobs for metal shaft (11.0) dia .433 (19.0) dia .748 (9.5) .374 (13.0) .512 (0.5) .020 (16.0) dia .630 (9.5) dia .374 (14.3) .563 (9.5) .374 (0.5) .020 (11.0) dia .433 (18.0) dia .709 (9.5) .374 (15.8) .622 (0.5) .020 polyester base: black polyamide tip colors: a, b, c, e, f, g, h material: polyacetal color: black polyester base: black polyamide tip colors: a, b, c, e, f, g, h at4103 small color tipped at4104 large color tipped at433 plain black a metal shaft knob options illustrated below with color choices actuators are fully rotational and operate either clockwise or counterclockwise. colors for actuators k and s: orange for real coded devices; yellow for complement coded devices actuation k plastic shaft adjusted by hand or with fat tipped screwdriver s dial adjusted by hand or with fat tipped screwdriver truth tables (circuits & positions) decimal hexadecimal 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 a b c d e f real coded model numbers: fr01fr, fr01kr, fr01sr, fr01ar 1 2 4 8 complement coded model numbers: fr01fc, fr01kc fr01sc, fr01ac 1 2 4 8 r c 10 16 actuator position x = on terminal no. (output) terminal numbers are actually on the switch. above sequence shown for clockwise rotation. color codes: a black b white c red e yellow f green g blue h gray mounting hardware is available if needed for models with actuator a: hexagon nut at513m, locking ring at515m, and lockwasher at509; all are shown in the accessories and hardware section. knob orientation: when installed with shaft fat rotated 180 from bushing fat as shown in typical switch dimensions, white line on cap points to actuator position 0 noted in truth tables below.
series fr01 10mm dip rotaries www.nkk.com g8 indicators accessories supplement tactiles keylocks pushbuttons illuminated pb slides programmable rockers touch tilt toggles g rotaries fr01fc10p fr01fr10h (7.62) .300 c l 12 48 (2.54) ty p .100 (0.8 ~ 1.0) dia ty p .031 ~ .039 (1.27) .050 c (10.0) .394 (0.2) .008 (3.8) dia .150 (10.0) .394 0 1 2 3 4 5 6 7 8 9 (3.8) .150 (2.1) .083 (7.62) .300 (3.3) .130 (0.2) ty p .008 c 1 2 4 8 (2.54) ty p .100 (0.5) ty p .020 (10.0) .394 (0.2) .008 (3.8) dia .150 (10.0) .394 0 1 2 3 4 5 6 7 8 9 a b c d e f (10.0) .394 (0.2) .008 (10.0) .394 0 1 2 3 4 5 6 7 8 9 (3.8) dia .150 (3.8) .150 (2.75) .108 (2.54) .100 (3.25) .128 (3.3) .130 (2.1) .083 (0.2) ty p .008 12 48 c (2.54) ty p .100 (0.5) ty p .020 0 1 2 3 4 5 6 7 8 9 a b c d e f (10.0) .394 (0.2) .008 (10.0) .394 (3.8) dia .150 (2.54) .100 c l 1 248 (2.54) ty p .100 (0.8 ~ 1.0) dia ty p .031 ~ .039 (1.27) .050 c decimal hexadecimal decimal hexadecimal typical switch dimensions p right angle pc ? screwdriver h right angle pc ? plastic shaft straight pc ? plastic shaft fr01kr16p fr01kc16h (7.62) .300 c l 12 48 (2.54) ty p .100 (0.8 ~ 1.0) dia ty p .031 ~ .039 (1.27) .050 c (2.54) .100 c l 1 248 (2.54) ty p .100 (0.8 ~ 1.0) dia ty p .031 ~ .039 (1.27) .050 c (10.0) .394 (0.2) .008 (10.0) .394 0 1 2 3 4 5 6 7 8 9 (10.0) .394 (0.2) .008 (10.0) .394 0 1 2 3 4 5 6 7 8 9 a b c d e f (3.8) .150 (2.1) .083 (7.62) .300 (3.3) .130 (0.2) ty p .008 (7.0) .276 (3.8) .150 c 1 2 4 8 (2.54) ty p .100 (0.5) ty p .020 0 1 2 3 4 5 6 7 8 9 (10.0) .394 (0.2) .008 (10.0) .394 0 1 2 3 4 5 6 7 8 9 a b c d e f (10.0) .394 (0.2) .008 (10.0) .394 (7.0) .276 (3.8) .150 (2.75) .108 (2.54) .100 (3.25) .128 (3.3) .130 (2.1) .083 (3.8) .150 (0.2) ty p .008 12 48 c (2.54) ty p .100 (0.5) ty p .020 decimal hexadecimal decimal hexadecimal p h straight pc ? screwdriver
series fr01 10mm dip rotaries www.nkk.com g9 indicators accessories supplement tactiles keylocks pushbuttons illuminated pb slides programmable rockers touch tilt toggles g rotaries fr01sr10p shown in position 0 with shaft fat rotated 180 from bushing fat typical switch dimensions straight pc ? dial p straight pc ? metal shaft p right angle pc ? metal shaft shown in position 0 with shaft fat rotated 180 from bushing fat h decimal hexadecimal (10.0) .394 (0.2) .008 (10.0) .394 1 2 3 4 5 6 7 (3.0) .118 (3.4) .134 (9.8) dia .386 (7.2) .284 (2.1) .083 (7.62) .300 (3.3) .130 (0.2) ty p .008 (0.5) ty p .020 c 1 2 4 8 (2.54) ty p .100 (7.62) .300 c l 12 48 (2.54) ty p .100 (0.8 ~ 1.0) dia ty p .031 ~ .039 (1.27) .050 c (7.62) .300 12 48 c c l (1.27) .050 (12.7) .500 (2.54) ty p .100 (0.8 ~ 1.0) dia ty p .031 ~ .039 (11.0) .433 (11.6) .457 (3.1) dia .122 (13.1) .516 (7.62) .300 flat m6 p0.75 (10.0) .394 (6.1) .240 (11.95) .470 (3.3) .130 (0.6) ty p .024 (2.28) .090 c (0.5) ty p .020 (0.4) ty p .016 (2.54) ty p .100 (12.7) .500 (0.2) ty p .008 1 2 4 8 12 48 c (3.3) .130 (0.4) ty p .016 (0.5) ty p .020 (2.54) ty p .100 (12.7) .500 flat m6 p0.75 (2.28) .090 (10.0) .394 (6.1) .240 (13.9) .547 (0.6) ty p .024 (3.03) .119 (7.62) .300 (0.2) ty p .008 (2.54) .100 (11.0) .433 (11.6) .457 (3.1) dia .122 (13.1) .516 (5.5) .217 (7.62) .300 12 4 8 c c l (1.27) .050 (12.7) .500 (2.54) ty p .100 (0.8 ~ 1.0) dia ty p .031 ~ .039 (2.54) .100 fr01ac16hb fr01ar10pb
series fr01 10mm dip rotaries www.nkk.com g10 indicators accessories supplement tactiles keylocks pushbuttons illuminated pb slides programmable rockers touch tilt toggles g rotaries packaging fr01f with screwdriver actuation & straight pc fr01f, fr01k & fr01s each stick-tube contains 50 switches. switches must be ordered in 50-piece increments. fr01a each stick-tube contains 25 switches. switches must be ordered in 25-piece increments. note: transport and storage temperatures should not exceed 50c (122f). store stick tubes on fat surface. s stick-tube fr01k with plastic shaft & right angle pc (16.2) .638 (16.6) .654 (540.0) 21.260 (15.6) .614 (15.9) .626 (530.0) 20.866 fr01s with dial actuation & straight pc fr01a with metal shaft & straight pc fr01a with metal shaft & right angle pc (12.5) .492 (14.1) .555 (528.0) 20.787 (390.0) 15.354 (33.6) 1.323 (18.2) .717 (13.1) .516 (35.5) 1.398 (390.0) 15.354
notes www.nkk.com g11
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: nkk switches: ? fr01kr16h-s? fr01fr16h-s? fr01kc10h-s? fr01kr10h-s? fr01kr16p-s? fr01kc16p-s? fr01fr10h-s? fr01fc16h-s? fr01kc16h-s? fr01fr10h? fr01fr16p? fr01fc10h-s? fr01kc10h? fr01kc10p? fr01kc16p? fr01kr10p-s? fr01fr10p-s? fr01kr10p? fr01kr16h? fr01kc10p-s? fr01kr16p? fr01fc16p? fr01fc10p? fr01fc16h? fr01fc10h? fr01fr16p-s? fr01fc16p-s? fr01fc10p-s? fr01ac10pb-w? fr01ac10pb-w-s? fr01ar10hb-06xl-s? fr01ar10pb-w-s? fr01ar16hb-06xl? fr01ar16hb-06xl-s? fr01ar16hb-06xl-w-s? fr01ar16pb-w-s? fr01fc10h-06xl-s? fr01fc10p-w-s? fr01fc16h-06xl-s? fr01fc16p-w-s? fr01fr10h- 06xl-s? fr01fr10p-w-s? fr01fr16h-06xl-s? fr01fr16p-w-s? fr01kc10h-06xl-s? fr01kc10p-w-s? fr01kc16h-06xl-s? fr01kc16p-w-s? fr01kr10h-06xl-s? fr01kr10p-w-s? fr01kr16h-06xl-s? fr01kr16p- w-s? fr01sc10p? fr01sc10p-w-s? fr01sr10p-w-s? fr01sr10p-s? fr01sc10p-s? fr01sc16p-s? fr01ar10pb-s? fr01ar10hb-s? fr01ar16pb-s? fr01ar16hb-s? fr01ac10pb-s? fr01ac10hb-s? fr01ac16pb-s? fr01ac16hb-s? fr01fc10h-06xl? fr01fc16p-w? fr01fr10h-06xl? fr01fr16h-06xl? fr01kc16h-06xl? fr01kr10h-06xl? fr01sc16p? fr01sr10p? fr01kr10p-w? FR01SR16P-s? fr01kr10h- 06xl-w? fr01fr16h-06xl-w? FR01SR16P
|
